EKDS12124-316 Floor standing, 1200x1200x400

The stainless steel double door compact floor standing enclosure range, EKDS, with a IP 55 protection degree is ideal for installation in confined spaces where a single door. when opened, would take up too much space in front of the enclosure. The doors' loading capacity also increases as it is divided over two doors. With an IP 55 protection degree, components inside the enclosure are well protected and makes the it well suited for almost any environment, grade dependant.

CE Declaration of Conformity GOST Kema Keur - DEKRA Lloyd's Register cULus_UL Listed IEC 61439 Declaration of Compliance
Feature: IP 55 TYPE 12, 13 IK 10; IP 66 TYPE 4X (on request)
EKDS Product Image
Characteristics  
Note IP 55, TYPE 12, 13, IK 10
Height 1200 mm
Width 1200 mm
Depth 400 mm
Mounting Plate
Height
1094 mm
Mounting Plate
Width
1094 mm
Weight (kg) 120.00
EKDS Catalogue drawing image
Item no.: EKDS12124-316
EAN no.: 8713574192027
  • Technical data
  • Features
  • Downloads
  • Certificates

Technical data

Material:

AISI 304L pre-grained stainless steel / AISI 316L. Body and removable rear panel: 1.5 mm. Door: 2 mm. Bottom Plates: 1.5 mm. Mounting plate: 3 mm.

Body:

One piece enclosure body. Integrated depth profiles with hole pattern allowing mounting plate adjustable in depth.

Door:

Surface mounted with 4 hinges including door frame with 25 mm hole pattern and earthing studs. Standard doors can not be reversed.

Rear panel:

Fitted by M6 torx screws. Standard facilities for rear door mounting. Split rear panels in 1600 mm wide enclosures.

Lock:

Espagnolette 4-point locking system in the main door and 2-point locking system in the slave door. Standard double-bit lock with 3 mm insert. Can be exchanged for standard inserts or Euro-cylinder and a lift handle.

Bottom plates:

One piece bottom plates with injected polyurethane gasket to ensure maximum sealing.

Earthing:

Door is equipped with separate welded earthing studs and earthing to the frame can be accomplished by using the ECF.

Mounting plate:

Double folded and slides into position. Adjustable in depth by steps of 25 mm. Mounting plate is delivered attached on the outside of the enclosure packaging. Fitted inside for 1600 mm wide enclosures. For 1600 mm wide, filler plate is included.

Finish:

240s pre-grained stainless steel (0.5 microns average).

Protection:

Double door version, complies with IP 55 | TYPE 12, 13 | IK 10. Individual doors with welded vertical divider, complies with IP 66 | TYPE 4X, 12 and 13 | IK 10.

Approvals:

CE, EAC, GOST, Kema Keur - DEKRA, Lloyd's Register, cULus_UL Listed.

Delivery:

One piece body with fitted door and rear panel, bottom plates and mounting plate, including door earthing studs. Delivered on a pallet which is identical to the width of the enclosure to allow suiting without removal. Mounting plate is attached to the outside of the enclosure packaging. All the packing material is recyclable.

Features

Feature:

Stainless steel 304 and 316(L) double door compact floor standing enclosures, with a IP 55 protection degree.

Advantage:

The space required immediately in front of the enclosure is reduced due to the width of each enclosure door being half that of the enclosure. This also results in the door's loading capacity being higher, as it is split over two doors. The installed components inside the enclosure will be safe and secure due to the high protection degree.

Benefit:

Large enclosures can be installed in areas where there is limited access space. The enclosure's doors can support heavy loads, such as, cooling units, due to its increased loading capability. Component failure and unnecessary downtime is avoided as water and dust are prevented from entering the enclosure. Stainless steel enclosures can be installed in almost any environment, grade dependent.

Comment:

Stainless steel 304 double door compact floor standing enclosures, with a high IP 66, TYPE 4X, protection degree, are also available.

CAD 2D drawing (DXF) EKDS12124 6 MB
CAD 2D drawing (PDF) EKDS12124-316 177 KB
CAD 3D drawing (STEP) EKDS12124 40 MB
CAD drawing (EMA) EKDS12124-316 EPLAN 230 KB
EPLAN P8 macros (ZIP) EKDS12124 STEP 10 MB
Image (JPG 591 x 800 px) EKDS Catalogue drawing image 114 KB
Image (JPG 600 x 600 px) EKDS Product Image 89 KB
Item sheet (PDF) EKDS12124-316 ENGLISH 81 KB
Mounting instructions document (PDF) Floor Standing Compact Stainless Steel 3 MB
Product sheet (PDF) EKDS 139 KB
Document (PDF) CE Declaration of Conformity 91 KB
Document (PDF) GOST 514 KB
Document (PDF) Kema Keur - DEKRA 227 KB
Document (PDF) Lloyd's Register 465 KB
Document (PDF) cULus_UL Listed 669 KB
Document (PDF) IEC 61439 Declaration of Compliance 82 KB