PF Front/rear Plinths

The front and rear plinth allows for cabling without any restrictions in accordance with the VDE 0113 standard. Installing cables is made easy as the plinth creates extra space underneath the enclosure.

PF Web Product Image HMI
  • Item list
  • Accessories
  • Technical data
  • Features
  • Downloads

Item list

Item no. Description Height
(mm)
Width
(mm)
PF1040 Plinth front/ rear, 100x400 100 400
PF1050 Plinth front/ rear, 100x500 100 500
PF1060 Plinth front/ rear, 100x600 100 600
PF1080 Plinth front/ rear, 100x800 100 800
PF1100 Plinth front/ rear, 100x1000 100 1000
PF1120 Plinth front/ rear, 100x1200 100 1200
PF2040 Plinth front/ rear, 200x400 200 400
PF2050 Plinth front/ rear, 200x500 200 500
PF2060 Plinth front/ rear, 200x600 200 600
PF2080 Plinth front/ rear, 200x800 200 800
PF2100 Plinth front/ rear, 200x1000 200 1000
PF2120 Plinth front/ rear, 200x1200 200 1200

For console 1600 mm wide use 2 x 800 mm wide plinth.

Range Mandatory Accessories Related Accessories Similar accessories Description
PS - - Plinth side panels for mild steel combinable and semi-compact floor standing enclosures.
PST - - Plinth side panels for mild steel consoles.
PCP - - Plinths can be combined and fixed to the floor before the enclosures are mounted on them with these profiles. Cables may be routed between bayed enclosures when these profiles are used.  
PV - - Ventilated plinth for mild steel floor standing enclosures with corner pieces and front and rear panels.
PFS - - Plinth for stainless steel floor standing enclosures with corner pieces and front and rear panels.
LF - -
LCR - -
CCB - - These wall mounting brackets for mild steel floor standing enclosures should be used when extra fixation is required.
CCBS - - These wall mounting brackets for stainless steel floor standing enclosures should be used when extra fixation is required.

Technical data

Description:

Front and rear plinth sections. For cabling without any restrictions and in accordance with the VDE 0113 standard. The plinth consists of four corner pieces with removable front covers. The side panels PS/PSK are to be ordered separately. Produced in 100 mm and 200 mm heights. 200 mm high plinths are delivered with a rear cover for cabling that consists of two removable panels 100 mm high. The front cover is a one piece panel of 200 mm high. All panels have double returns on each side for added strength.

Material:

Corner pieces in 2 mm and panels in 1.5 mm mild steel.

Finish:

RAL 7022 structured powder coating.

Pack quantity:

1 set of 4 corner pieces including covers. Front and rear panel (2 rear panels for 200 mm high plinths) with mounting accessories. Mounting accessories for side panels PST.

Mounting requirement:

Add the side panels PS for a complete plinth. When combining enclosures it is recommended to add transversal panels PCP for cable duct support and extra rigidity.

Features

Feature:

Painted steel plinth with front and rear removable panels for mild steel floor standing enclosures.

Advantage:

The plinth is mounted underneath the enclosure to provide extra space between the installation floor and the enclosure's bottom plates, this space is accessible by removing the front or rear panel.

Benefit:

Installing cables into the enclosure can be done easily as the plinth creates extra space below the enclosure. This extra space allows the installer to route the cables through the plinths for bayed enclosures. The plinth allows enclosures to be fixed to the floor without the need for interior access.

Comment:

The front and rear plinth PF, must be mounted along with side panels PS. If creating an enclosure system with multiple enclosures then the side panels are required to be mounted at the beginning and end only. To reinforce the combined plinths, plinth combining profiles PCP/PCPK, should be used.

Image (JPG 600 x 600 px) PF Web Product Image HMI 73 KB
Mounting instructions animation (.MP4) Floor standing PF-PS 4 MB
Mounting instructions document (PDF) Floor standing PF_PV_PS 5 MB
Product sheet (PDF) PF(ENGLISH) 60 KB