MCDS Stainless steel combinable version, double door enclosure

The stainless steel double door combinable floor standing enclosure range, MCDS, is ideal for installation in confined spaces where a single door, when opened, would take up too much space in front of the enclosure. The doors' loading capacity also increases as it is divided over two doors. With a IP 55 protection degree, components inside the enclosure are well protected and makes it well suited for almost any environment, grade dependent.

CE Declaration of Conformity DNV-GL EAC GOST IP Declaration of Compliance Kema Keur - DEKRA Lloyd's Register cULus_UL Listed IEC 61439 Declaration of Compliance
Feature: IP 55 TYPE 12 IK 10
MCDS Product Image
MCDS Catalogue drawing image
  • Item list
  • Technical data
  • Features
  • Downloads
  • Certificates

Item list

Item no. Description Height
Mounting Plate
Mounting Plate
MCDS18105 Floor standing, 1800x1000x500 1800 1000 500 1694 894 153.00
MCDS18105-316 Floor standing, 1800x1000x500 1800 1000 500 1694 894 153.00
MCDS18125 Floor standing, 1800x1200x500 1800 1200 500 1694 1094 173.00
MCDS18125-316 Floor standing, 1800x1200x500 1800 1200 500 1694 1094 173.00
MCDS20126 Floor standing, 2000x1200x600 2000 1200 600 1894 1094 192.00
MCDS20126-316 Floor standing, 2000x1200x600 2000 1200 600 1894 1094 192.00

Technical data


AISI 304L pre-grained stainless steel / AISI 316L. Frame: 1.5 mm. Door: 2 mm. Rear, roof and side panels: 1.5 mm. Bottom plates: 1.5 mm stainless steel. Mounting plate: 3 mm galvanized steel.


Seam welded reversed open profiles with 25 mm hole pattern, according to DIN 43660.


Mounted with four hinges. Including door frame with 25 mm hole pattern. Doors cannot be reversed. Separate doors to be ordered for left hand door locking.

Rear panel:

Fitted by M6 torx screws. Standard facilities for rear door mounting. Split rear panels in 1600 mm wide enclosures.

Side panels:

Supplied as an accessory.

Roof panel:



Espagnolette 4-point locking system in the main door and 2-point locking system in the slave door. Standard double-bit lock with 3 mm insert. Standard inserts, cylinders, lift handles and T-handle are available as accessories.

Bottom plates:

Two piece bottom plate in 1200 mm width, with injected polyurethane gasket to ensure maximum sealing.

Mounting plate:

Double folded and adjustable in depth by steps of 25 mm, with the MPD02 accessory. Mounting plate is delivered, attached on the outside of the enclosure packaging.


All panels are earthed through their fittings and are equipped with a separate earthing stud.


400 pre-grained stainless steel.


Complies with IP 55 | TYPE 12 | IK 10.

Mounting requirements:

Standard delivery ready for combined installation. For stand-alone installation, add side panels.


Frame with fitted doors, rear panel, roof panel, bottom plates, mounting plate and door frame. Delivery also includes earthing bolts. Delivered on a pallet which is identical to the width of the enclosure to allow baying without removal. Packing material is recyclable.



Stainless steel 304 and 316(L) double door combinable floor standing enclosures, with a IP 55 protection degree.


A flexible solution that allows customers to create enclosure configurations made up of smaller individual enclosures. The space required immediately in front of the enclosure is reduced due to the width of each enclosure door being half that of the enclosure. This also results in the door's loading capacity being higher, as it is split over two doors. The installed components inside the enclosure will be safe and secure due to the high protection degree.


Large enclosure configurations can be created and installed in areas where there is limited access space. The enclosure's doors can support heavy loads, such as, cooling units, due to its increased loading capability. Component failure and unnecessary downtime is avoided as water and dust are prevented from entering the enclosure. Stainless steel enclosures can be installed in almost any environment, grade dependent.


Stainless steel side panels, SPMS, need to be ordered separately, to close individual enclosures and enclosure assembly's, to ensure the stated protection degree is achieved.

General drawing (PDF) MCDS General Drawing 547 KB
Image (JPG 591 x 800 px) MCDS Catalogue drawing image 122 KB
Image (JPG 600 x 600 px) MCDS Product Image 53 KB
Mounting instructions document (PDF) Floor standing stainless steel combinable 56 MB
Product sheet (PDF) MCDS(RUSSIAN) 1 MB
Document (PDF) CE Declaration of Conformity 100 KB
Document (PDF) DNV-GL 368 KB
Document (PDF) GOST 7 MB
Document (PDF) IP Declaration of Compliance 256 KB
Document (PDF) Kema Keur - DEKRA 275 KB
Document (PDF) Lloyd's Register 629 KB
Document (PDF) cULus_UL Listed 669 KB
Document (PDF) IEC 61439 Declaration of Compliance 102 KB